nixos-hardware/purism/librem/5r4/README.md
2023-09-03 07:29:12 +02:00

133 lines
4.8 KiB
Markdown

# Purism Librem 5 revision 4
Purism's [Librem 5] is a privacy-oriented Linux-friendly smartphone.
[Librem 5]: https://puri.sm/products/librem-5/
## Installation procedure
> *Note*
>
> TODO: build a uuu-compatible installer.
Until there's a native installer, the easiest way to install NixOS on Librem 5 seems to be using [Jumpdrive].
[Jumpdrive]: https://github.com/dreemurrs-embedded/Jumpdrive
### Jumpdrive
Jumpdrive is a tiny Linux distribution which presents device's internal storage as USB mass storage when you connect it to a PC.
It also provides a shell session over telnet.
Follow the instructions in the repo to boot into Jumpdrive.
Note that `uuu` is part of `nxpmicro-mfgtools` package in nixpkgs.
Now, plug the device into your PC. A new block device representing Librem 5's internal MMC should appear in `/dev`.
Note down this device path.
### U-Boot
> **Note**
>
> While upstream u-boot does support Librem 5, it can only boot using `boot.scr`, for which NixOS has no native support.
>
> There's work on extlinux support in Librem 5's U-Boot here: https://source.puri.sm/a-wai/uboot-imx/-/tree/allow-compressed-kernel
>
> This U-Boot version is packaged in the [`u-boot`] directory.
[`u-boot`]: ./u-boot
Provided you have a way to build Nix derivations for `aarch64-linux` (like a remote builder, [binfmt emulation], or you're building it on the phone itself), just run `nix-build u-boot/build.nix`.
[binfmt emulation]: https://search.nixos.org/options?channel=22.11&show=boot.binfmt.emulatedSystems&from=0&size=50&sort=relevance&type=packages&query=binfmt
> **Warning**
>
> Even though I've tested this myself, I can't guarantee that this will not render your device unbootable.
> Proceed with caution.
>
> If it does not work, your best bet is to follow the advice here, which will flash U-Boot build by upstream: https://forums.puri.sm/t/can-someone-with-serial-console-access-try-nixos-kernel-on-librem-5/19121/27
To flash the device, run
```console
$ sudo u-boot-install-librem5 <path to librem 5's MMC>
```
At this point, if you have an OS installed on your Librem 5, it's best to reboot into it to check that the U-Boot was flashed correctly.
If that's the case, reboot back into Jumpdrive.
### Partitioning
Now, from your host system, partition the MMC.
> **Warning**
>
> Doing this wipes all data off the phone
I went with 1 bootable `ext2` partition for `/boot`, and one `ext4` partition for `/`.
It ended up looking like this (your device names will be different):
```console
$ sudo fdisk -l /dev/mmcblk0
Disk /dev/mmcblk0: 29.12 GiB, 31268536320 bytes, 61071360 sectors
Units: sectors of 1 * 512 = 512 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disklabel type: dos
Disk identifier: 0xcec26c32
Device Boot Start End Sectors Size Id Type
/dev/mmcblk0p1 * 4096 499711 495616 242M 83 Linux
/dev/mmcblk0p2 499712 61071359 60571648 28.9G 83 Linux
```
Note 2MiB of free space before the first partition.
This is where U-Boot lives.
Mount the partitions on your host system, e.g. to `/mnt` and `/mnt/boot`.
Remember that `/mnt` is the second partition, and `/mnt/boot` is the first.
### Installation
Now, write your NixOS config.
Use `/dev/mmcblk0p1` as `fileSystems."/boot"` and `/dev/mmcblk0p2` as `fileSystems."/"`.
Don't forget to import the [module from this directory](./default.nix).
If you plan to use the device as a smartphone, you have a choice of two "desktop" (?) environments packaged in nixpkgs: [phosh] and [Plasma Mobile].
[phosh]: https://search.nixos.org/options?channel=22.11&show=services.xserver.desktopManager.phosh.enable&from=0&size=50&sort=relevance&type=packages&query=phosh
[Plasma Mobile]: https://search.nixos.org/options?channel=22.11&show=services.xserver.desktopManager.plasma5.mobile.enable&from=0&size=50&sort=relevance&type=packages
Build the configuration (`nix build .#nixosConfigurations.<hostname>.config.system.build.toplevel` if you're using flakes).
Running `nixos-install --system ./result --root /mnt` will copy the system to the MMC.
Unless you're running on an aarch64 system, it will fail to activate or install the bootloader, however.
You must do this manually.
Get a shell on Jumpdrive, mount partitions there, and activate the system:
```console
$ nc 172.16.42.1 23
# mkdir /mnt
# mount /dev/mmcblk0p2 /mnt
# mkdir -p /mnt/boot
# mount /dev/mmcblk0p1 /mnt/boot
# chroot /mnt /nix/var/nix/profiles/system/activate
# chroot /mnt /nix/var/nix/profiles/system/bin/switch-to-configuration boot
```
Provided the last command succeeds, you now should have a bootable device.
Unmount:
```console
# sync
# umount /mnt/boot
# umount -l /mnt
# echo u > /proc/sysrq-trigger
# echo s > /proc/sysrq-trigger
```
And shut the phone down by holding the power key.
Start it up and you should be booting straight into your NixOS installation.